DTM-7.4 Network

Change the settings of the Network function.  
    • When LAN is configured with a DHCP, set "DHCP" to "Enable" to configure t be setting automatically.         ("Enable" is set by default) To assign fixed IP addresses to each components, you must set "DHCP" to         "Disable", assign an address to this unit in the "IP Address" setting, and set information related to
        your LAN, such as Subnet Mask and Gateway.
Wi-Fi (Default Value: Off(Wired))
Connect the unit to the network via a wireless LAN router.
• When switching between "On" and "Off(Wired)", stop the Network service.  Also, when group playback is in process, cancel the group playback once, and then switch the setting.

On	Wireless LAN connection
Off(Wired)	Wired LAN connection

Wi-Fi Setup (Default Value: -)
Configure wireless LAN settings by pressing Enter with "Start" displayed.
Wi-Fi Status (Default Value: -)
The information of the connected access point is displayed.

SSID	SSID of the connected access point
Signal	Signal strength of the connected access point
Status	Status of the connected access point

MAC Address (Default Value: -)

Check the MAC address of this unit. This value is specific to the component and cannot be changed.

DHCP (Default Value: Enable)

Enable	Auto configuration by DHCP
Disable	Manual configuration without DHCP • If you select "Disable", set "IP Address", "Subnet Mask", "Gateway", and "DNS Server" manually.

IP Address (Default Value: 0.0.0.0)

Displays/Sets the IP address.

Subnet Mask (Default Value: 0.0.0.0)

Displays/Sets the subnet mask.

Gateway (Default Value: 0.0.0.0)

Displays/Sets the gateway.

DNS Server (Default Value: 0.0.0.0)

Displays/Sets the primary DNS server.

Proxy URL (Default Value: -)

Displays/Sets the proxy server URL.

Proxy Port (Default Value: 8080)

Displays/Sets the proxy server port number when you input "Proxy URL".

Friendly Name (Default Value: Integra DTM-7.4 XXXXXX)

Change the model name of this unit which is displayed on the device
connected to the network to an easily recognized name.
1. Press Enter to display the Edit screen.
2. Select a character or symbol with the cursors, and press Enter.
Repeat this operation to input up to 31 characters.
"A/a": Switches between upper and lower cases.
"←" "→": Moves the cursor in the arrow direction.
" ": Removes a character on the left of the cursor.
" ": Enters a space.
• Pressing CLR on the remote controller will remove all the input characters.
3. After inputting, select "OK" with the cursors, and press Enter.The input name will be saved.

AirPlay (Default Value: On)

Select whether or not to use the AirPlay function.

On	When this function is used.
Off	When this function is not used.

AirPlay Device Name (Default Value: Integra DTM-7.4 XXXXXX)

Change the model name of this unit which is displayed on the AirPlay connected
device to an easily recognized name.
1. Press Enter to display the Edit screen.
2. Select a character or symbol with the cursors, and press Enter.
Repeat this operation to input up to 31 characters.
"A/a": Switches between upper and lower cases.
"←" "→": Moves the cursor in the arrow direction.
" ": Removes a character on the left of the cursor.
" ": Enters a space.
• Pressing CLR on the remote controller will remove all the input characters.
3. After inputting, select "OK" with the cursors, and press Enter.
The input name will be saved.
• This function cannot be used when registering this unit to Home App.

AirPlay Password (Default Value: -)

You can set a password of up to 31 characters so that only users that have input can use AirPlay.
1. Press Enter to display the Edit screen.
2. Select a character or symbol with the cursors, and press Enter.
Repeat this operation to input up to 31 characters.
"A/a": Switches between upper and lower cases.
"←" "→": Moves the cursor in the arrow direction.
" ": Removes a character on the left of the cursor.
" ": Enters a space.
• To select whether to mask the password with "" or display it in plain text,
press Menu on the remote controller.
• Pressing CLR on the remote controller will remove all the input characters.
3. After inputting, select "OK" with the cursors, and press Enter.
The input password will be saved.
• This function cannot be used when registering this unit to Home App.

Privacy Statement (Default Value: Not Accepted)

When using a network service that requires a login name, email address, password, etc., you need to agree to the Privacy Statement of our company.
• This setting can be made after confirming the Privacy Statement.
• When "Not Accepted" is selected, the login name, email address, password,
etc., that are kept on this unit will be deleted and you will be logged out from
the network service you have logged in.

Network Check (Default Value: -)

You can check the network connection.
Press Enter when "Start" is displayed.

• Wait for a while if "3. Network" cannot be selected. It can be selected when the network function is activated.